manuals/manuals_Support_Center_Ion_20Megatouch_20Wallette_20__20Entertainer_Monitor

15” Monitor Removal

1. Turn off and unplug the game.

2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then

unlock and open the CPU section.

3. Remove the screw and washer fastening the strain relief cord, then remove the remaining 5 screws

fastening the LCD mounting bracket to the game. The key socket ground wire will also be re-
moved in the process. See Figure 1.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge

Megatouch Ion Technical Reference Manual

KEY SOCKET

ASSEMBLY

TOUCHSCREEN
CONTROLLER
CABLE ON
TOUCHSCREEN
CONTROLLER

OSD

BOARD

LCD MOUNTING

BRACKET

VGA MONITOR CABLE

OSD
CABLE

VGA MONITOR CABLE

GROUND WIRE

TOUCHSCREEN
CONTROLLER
CABLE GROUND

WIRE

TOUCHSCREEN
POWER CABLE

FIGURE 1 - CLOSE-UP OF CPU SECTION

4. Remove the nut, wire and bolt from the key socket assembly located on LCD mounting bracket,

then remove the bracket. See Figure 1.

5. Carefully cut the tie wraps around the VGA monitor cable and remove the ground wire. Discon-

nect the cable from the monitor and the motherboard. See Figure 1. Unscrew the bracket on the
underside of the I/O board to release the cable.

6. Remove the OSD cable from the twist clamp and disconnect it from the OSD board and the

monitor. Then remove the OSD board from the Velcro attached to the back of the monitor and set
it aside. See Figure 1.

8. Carefully cut the tie wrap around the touchscreen controller cable and disconnect the cable from

the touchscreen controller. Also remove the ground wire. See Figure 1.

9. Disconnect the touchscreen power cable from the touchscreen controller (see Figure 1), then

disconnect the Molex connector identified by the orange and gray wires.

10. Loosen the 6 screws (3 per hinge) on the monitor side of the hinges in order to raise the hinges

and allow room to remove the monitor. See Figure 2.

NOTE:

Elite Edge games may require you to remove the joystick in order to allow the necessary

room for loosening of the hinge screws. To remove the joystick, carefully place the game on its
side. Remove the 2 screws securing the protective bracket on the bottom of the game and re-
move the bracket. Disconnect the joystick connector and remove the joystick. Return the game
to its upright position.

11. Slide the monitor out of the bezel.

12. If you will not be reusing the existing touchscreen, continue with installing the new monitor. If you

will be reusing the touchscreen, note the orientation of the screen (i.e. the positioning of the ribbon
cable and which side is the front) before removing it from the monitor. Then use dental floss to
carefully cut the foam tape holding the screen to the monitor. Once the touchscreen is completely
free from the monitor, remove any residual foam tape from the screen with denatured alcohol and
clean the glass with the supplied alcohol wipe.

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge

Megatouch Ion Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge (cont’d)

CPU SIDE OF HINGE

MONITOR
SIDE OF
HINGE

LCD POWER CONNECTOR

FIGURE 2 - CLOSE-UP OF MONITOR HINGE

7. Disconnect the LCD power connector (black and yellow wires). See Figure 2.

15” Monitor Installation

1. If you will not be using the touchscreen from your original monitor, skip to step 3. If you will be

using the original touchscreen, clean the glass on the new LCD monitor with the supplied alcohol
wipe, then cut pieces of the supplied 1/2” foam tape long enough to cover each edge of the monitor
without overlapping. After the tape is in place on the monitor, peel off the backing.

2. Carefully place the touchscreen over the monitor in the same manner it was attached to the old

monitor, making sure the screen is properly and evenly aligned over the glass. Clean the front of
the touchscreen with the supplied alcohol wipe once it is in place.

3. Carefully slide the new monitor into the bezel, making certain that the white edge of the monitor

and the monitor wire connections are facing the bottom of the bezel. Ensure that the monitor is
properly centered, then tighten the hinge screws. See Figure 2.

NOTE:

If you removed the joystick on your Elite Edge, carefully return the game to its side and

reconnect the joystick to the connector in the game. Place the protective bracket in its previous
position, sliding it under the lazy Susan and making sure the cutouts are placed around the installed
screws. Make sure all wires are secured inside the bracket, then reinstall the 2 screws securing
the bracket. Return the game to its upright position.

4. Install the supplied LCD mounting bracket and fasten it to the game with the 6 screws. One screw

(and washer) will fasten the strain relief cord, while another will secure the blue ground wire for the
key socket. See Figure 1.

5. Replace the key socket assembly by securing the bolt, green wire and nut over the LCD mounting

bracket. See Figure 1.

6. Connect the touchscreen controller cable to the touchscreen controller and secure it with a tie

wrap. Also restore the touchscreen controller cable ground wire. See Figure 1.

7. Connect the touchscreen power cable to the touchscreen controller (see Figure 1) and reconnect

the Molex connector (orange and gray wires).

8. Connect the LCD power connector (black and yellow wires). See Figure 2.

9. Reattach the OSD board to the Velcro on the back of the monitor, then connect the new OSD

cable to both the OSD board and the monitor. See Figure 1. Secure the cable in the twist clamp.

10. Connect the new VGA cable to both the monitor and the motherboard. Run the cable beneath the

I/O board mounting plate and secure it in place with the bracket and 2 screws. See Figure 3. Also
replace the ground wire.

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge

Megatouch Ion Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge (cont’d)

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge (cont’d)

BRACKET

SCREWS
(2 PLACES)

FIGURE 3 - BRACKET AND SCREWS SECURING VGA MONITOR IN PLACE

11. Tie wrap the VGA monitor cable and the OSD cable.

12. Close and lock the CPU section.

13. Plug in and turn on the game.

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge

Megatouch Ion Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Megatouch Ion Technical Reference Manual

17” Monitor Removal

1. Turn off and unplug the game.

2. Unlock and open the CPU section.

Very

carefully

cut the tie wraps securing the touchscreen controller cable to the touchscreen

controller. Then, disconnect the cable from the touchscreen controller. See Figure 4.

4. Release the touchscreen controller ribbon cable from the cable clamp.

5. Cut the tie wrap securing the touchscreen controller cables and speaker wires on the back of the

monitor (see Figure 4).

6. Cut the tie wrap securing the orange and gray wires and ground wire from the touchscreen controller

and the OSD cable. See Figure 4.

7. Remove the touchscreen controller cable, the orange and gray wires (from the touchscreen

controller) and the OSD board cable from the cable twist lock. See Figure 4.

FIGURE 4 – FORESEESON MONITOR IN 17” ION COUNTERTOP GAME

SCREWS

SECURING

LCD BRACKET

TO GAME

(6 PLACES)

OSD BOARD

TOUCHSCREEN
CONTROLLER
CABLE

INVERTER

2-PIN LCD

CONNECTOR

OSD BOARD

CONNECTOR

VGA

CONNECTOR

SCREWS

SECURING THE

MONITOR SIDE

OF HINGE

(3 PER SIDE)

VGA AND

TOUCHSCREEN

CONTROLLER

GROUND WIRES

SECURE STRAIN
RELIEF CORD HERE

CABLE TIE WRAP
SECURING T/S
CONTROLLER
CABLES AND
SPEAKER WIRES

TIE WRAP SECURING
ORANGE AND GRAY
WIRES AND GROUND
WIRE FROM T/S
CONTROLLER AND
OSD CABLE

CABLE TWIST LOCK
SECURING T/S

CONTROLLER CABLE,
ORANGE AND GRAY
WIRES FROM T/S
CONTROLLER, AND
OSD CABLE

TOUCHSCREEN

CONTOLLER

RIBBON CABLE

ROUTED

THROUGH LCD

MOUNTING

BRACKET

CABLE TIE

WRAP

SECURING

VGA CABLE

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Megatouch Ion Technical Reference Manual

8. Carefully remove the 2 screws securing the touchscreen controller to the LCD mounting bracket.

Carefully remove the controller and the nylon spacers underneath (if applicable). Set the controller
aside.

9. Disconnect the 2-pin LCD connector, the OSD connector and the VGA connector from the back of

the monitor. See Figure 4.

10. Remove the screw and washer securing the VGA and touchscreen controller ground wires to the

back of the monitor. See Figure 4.

11. Remove the OSD board and inverter from the Velcro attached to the back side of the monitor and

set them aside. See Figure 4.

12. Place something in front of the game to brace the bezel once the strain relief cord is undone, then

remove the screw and washer securing the strain relief cord. See Figure 4.

13. Remove the remaining 5 screws fastening the LCD mounting bracket to the game. See Figure 4.

14. Route the touchscreen controller cable through the hole in the LCD mounting bracket and set the

LCD mounting bracket aside.

15. Loosen the 6 screws on the monitor side of the hinges (3 screws per hinge) in order to raise the

hinges and allow enough room to remove the monitor. Be careful to keep the hinge spacers in
place beneath the hinges.

16. Carefully remove the monitor from the bezel.

17. If you will be reusing the existing touchscreen, note the orientation of the screen (i.e. the positioning

of the ribbon cable and which side is the front) before removing it from the LCD monitor. Then, use
dental floss to carefully cut the foam tape holding the touchscreen to the monitor until you are able
to completely remove the screen. You will need to place the touchscreen on a stable surface until
it is installed on the new monitor. Then remove any residual foam tape from the reverse side of the
screen with denatured alcohol.

17” Monitor Installation

18. Clean the glass on the new monitor with the supplied alcohol wipe, then cut pieces of the supplied

1/2" foam tape long enough to cover each edge of the monitor without overlapping. After the tape is
in place on the monitor, peel off the backing.

19. Carefully place the supplied or existing touchscreen over the monitor in the same manner it was

attached to the old monitor, making sure the screen is properly and evenly aligned over the glass.
Clean the front of the touchscreen with the supplied alcohol wipe once it is in place.

20. Carefully place the new monitor into the bezel so that the monitor connections are nearest to the

hinges. Make sure the monitor is properly centered.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Megatouch Ion Technical Reference Manual

21. Route the touchscreen controller cable through the hole in the LCD mounting bracket (Figure 4).

22. Fasten the strain relief cord under the LCD mounting bracket screw designated in Figure 4. Replace

the remaining 5 screws securing the mounting bracket to the bezel. See Figure 4.

23. Tighten the 3 screws per hinge that were loosened during removal of your old monitor. See Figure

4. Make sure the spacers beneath the hinges are aligned correctly as you tighten the screws.

24. Carefully attach the cable to the touchscreen controller, making sure that the cable’s pins are

correctly aligned. Secure the cable in place using the 2 provided black tie wraps.

25. Install the 2 existing nylon spacers on the standoffs where the touchscreen controller will be mounted

(see Figure 4). If your touchscreen controller did not have nylon spacers, install the 2 provided
spacers. Then, secure the touchscreen controller to the standoffs on the LCD mounting bracket
using the existing screws.

26. Secure the ribbon cable from the touchscreen controller in the cable clamp on the LCD mounting

bracket. See Figure 4.

27. Add the “loop” side of the provided Velcro (the mating side of the Velcro attached to the OSD board

and inverter) to the back of the monitor in the same locations as the old monitor. Replace the OSD
board and inverter on the Velcro.

28. Connect the 2-pin LCD connector to the back of the monitor. See Figure 4.

29. Connect the OSD connector to the monitor. See Figure 4.

30. Connect the VGA monitor connector to the monitor. See Figure 4.

31. Replace the screw and washer securing the VGA and touchscreen controller ground wires to the

back of the monitor. See Figure 4.

32. Replace the touchscreen controller cable, the orange and gray wires (from the touchscreen

controller) and the OSD board cable in the cable twist lock as shown in Figure 4.

33. Adhere the provided cable tie wraps to the back of the monitor in the same locations as the old

monitor.

34. Thread the provided tie wrap through the adhesive cable tie wraps just installed and secure the

touchscreen controller wires and OSD cable wires in the cable tie wrap shown in Figure 4. Secure
VGA cable in the other cable tie wrap in the same fashion.

35. Dress the remaining wires using the supplied tie wrap.

36. Close and lock the CPU section.

37. Plug in and turn on the game.